Search found 456 matches
- Jul 22nd, '23, 16:19
- Forum: Cape Dory Sailboats
- Topic: Typhoon compression post
- Replies: 5
- Views: 550
Re: Typhoon compression post
I installed a removable compression post in my 1976 Typhoon as a preventative measure. When refurbishing the boat 15 years ago I noticed a few small cracks along the base of the cabin where it merges into the deck. This is the indication that they=re may have been some compression in the past. It ha...
- Jul 10th, '23, 09:49
- Forum: Cape Dory Sailboats
- Topic: Few questions on Typhoon
- Replies: 17
- Views: 1559
Re: Few questions on Typhoon
Definitely plan on re-bedding all deck hardware since the bedding material from the factory has dried out. Also I discovered that the factory used a minimal amount of bedding compound leaving leaks to the core under several fittings. Also check the backing plates for the chain-plates - They only use...
- Apr 27th, '23, 18:30
- Forum: Buy/Sell CD Boats & Gear
- Topic: SOLD --- Cape Dory Typhoon
- Replies: 9
- Views: 864
Re: FS: Cape Dory Typhoon
What a gorgeous Typhoon!
- Apr 5th, '23, 14:39
- Forum: Buy/Sell CD Boats & Gear
- Topic: Typhoon Genoa for sale
- Replies: 2
- Views: 342
Re: Typhoon Genoa for sale
The genoa is still available has green UV protection. I used it with the FF1 roller furling system. If still interested send me a pm and we can discuss the transaction, shipping etc.
.
.
- Mar 7th, '23, 21:46
- Forum: Cape Dory Sailboats
- Topic: Hoist Launching Typhoon
- Replies: 10
- Views: 713
Re: Hoist Launching Typhoon
You could easily ramp launch - depending on the depth of the water and characteristics of the trailer.Movable bunks would be easier than jack-stands on a trailer. If you have 3-3.5 feet of water, a good truck should be able to launch it without a tongue extension although tong extensions make it a l...
- Mar 7th, '23, 21:38
- Forum: Cape Dory Sailboats
- Topic: Beautiful Pictures of a Cape Dory 22, CD22 - Salvagable?
- Replies: 17
- Views: 1268
Re: Beautiful Pictures of a Cape Dory 22, CD22 - Salvagable?
I rescued a Typhoon that was in MUCH worse condition than this nice boat. Upgrading the forestay may not be a problem if you decide to put a roller furler in place. The teak rubrail and toe rail may have to all come off then insert new sections and do a complete re-bedding (not a bad idea anyway). S...
- Dec 15th, '22, 17:56
- Forum: Cape Dory Sailboats
- Topic: Restoring a Cape Dory Typhoon Weekender help
- Replies: 4
- Views: 496
Re: Restoring a Cape Dory Typhoon Weekender help
WOW! A lot of ideas. I restored a 1976 Typhoon with many serious hull issues. Bilge: I do not like placing foam in these areas since it can hold water and make for some ugly problems. The keel is molded lead that was sealed in the bilge. There is an eye that was used for placing the ballast into the...
- Oct 18th, '22, 22:36
- Forum: Cape Dory Sailboats
- Topic: Sail Repair Tape or Patches
- Replies: 3
- Views: 278
Re: Sail Repair Tape or Patches
self sticking sail repair tape is only temporary. However you can prevent it from coming off by rounding the corners and when applying it, place sail on a flat surface and firmly press it onto a clean sail (no salt residue). Do not touch the sticky surface because the oils in your skin will weaken t...
- Oct 2nd, '22, 22:50
- Forum: Cape Dory Sailboats
- Topic: Winter cover frame
- Replies: 17
- Views: 888
Re: Winter cover frame
WInter Cover Frame.jpeg Poly pipes are attached to mast with 14 gauge wire passed through holes drilled into the pipe. Ends of poly pipe also have holes drilled through them to pass small diameter rope to attach to trailer (or cradle) and snugged tight. Mast had been positioned on supports high eno...
- Sep 22nd, '22, 09:43
- Forum: Cape Dory Sailboats
- Topic: mainsail leech flutter
- Replies: 10
- Views: 514
Re: mainsail leech flutter
When you think you might be reefing do it! Most people tend to hang on to the full main way too long. Actually in that wind and point of sail a reefed main, will do much better. Also perhaps the genny or jib cars could be pulled aft a few notches to reduce backwinding the main. You were actually sai...
- Sep 19th, '22, 23:07
- Forum: Cape Dory Sailboats
- Topic: Winter cover frame
- Replies: 17
- Views: 888
Re: Winter cover frame
I have used 1.25" 100 and 160 psi poly pipe spaced about 14" along the mast. Drill holes in the ends and cut the hoops long enough to go over the mast and just past the gunwales. I also made a frame to support the mast keeping it 4 feet off the deck. Tie the hoops to the mast to keep them ...
- Sep 15th, '22, 19:24
- Forum: Cape Dory Sailboats
- Topic: Is it safe to put this in the water?
- Replies: 13
- Views: 767
Re: Is it safe to put this in the water?
Nice looking photo - make a large print then frame it so you can think about such a nice boat all winter when it is covered. You made the rudder and bottom safe - nice job! Congratulations on your success with such a great sailing Ty - I really like mine!
- Sep 5th, '22, 16:28
- Forum: Cape Dory Sailboats
- Topic: Loose-footed main for a Typhoon
- Replies: 7
- Views: 464
Re: Loose-footed main for a Typhoon
Timely question - I am also contemplating a new main with a loose-footed design. I had one on a larger boat but it had easier outhaul controls. Once you set up the outhaul at the mooring it should only take a little tweaking while underway. I really liked the loose footed main - made it MUCH easier ...
- Aug 18th, '22, 13:55
- Forum: Cape Dory Eye Candy
- Topic: Arietta...Engineless!
- Replies: 9
- Views: 1180
Re: Arietta...Engineless!
That is what a sailboat should look like!
- Aug 18th, '22, 13:38
- Forum: Cape Dory Project Descriptions & Project Photos
- Topic: Typhoon Weekender #1508 - Hull gelcoat replacement
- Replies: 9
- Views: 1421
Re: Typhoon Weekender #1508 - Hull gelcoat replacement
Have you tried a random orbital sander with 60 or coarser grit for the final sanding. Works better than a grinder but uses a lot of discs! I borrowed several short jack stands from the local marina to elevate the Typhoon off the trainer so as to work on the keel and then add 3 coats of barrier coat....