Companion way boards
Moderator: Jim Walsh
Companion way boards
I want to replace the single piece companion way drop board on my Typhoon (#1671), which is start to delaminate. I'm thinking of using three solid teak boards as I have seen on other Ty's. Any suggestions? Also has anyone used something like lexan? Can you get it at home depot? Is it easy to cut?
Lexan Washboards
You can use lexan but it's not inexpensive and it's not easy to cut unless you have the right equipment. Don't forget they use it for bullet proof "glass" sometimes. When exposed to UV it discolors with age and also tends to show scratches and stress lines -- at least that's what my dodger windows made of lexan did. I doubt if Home Base would have it, but you can get it at a glass shop and they also have the tools to cut it to size for you.
- johnny of STORK
- Posts: 97
- Joined: Feb 7th, '05, 18:51
- Location: Cape Dory 30 #240 STORK
Taos, NM
San Carlos, Sonora, MX - Contact:
Cutting Lexan
I just cut some large sheets of 1/2" Lexan a couple of weeks ago with a sharp skilsaw -- it cuts like a dream. Plexiglas is the one that shatters. It might discolor, but I doubt if it ever would show crazing or stress-cracking. On the other hand, it does scratch quite easily. If you cut it, you need to leave the protective sheeting on it until you are done. I don't know what it costs -- it was provided by a customer for a fabrication job.
Johnny
Johnny
- Bill
- Posts: 56
- Joined: Feb 9th, '05, 06:50
- Location: S/V - CD28 Morning Light:
Chebeague Island, Maine (offshore)
companionway
Allan...I assume your board is plywood since it is delaminating. Best bet is to do it right and use three teak boards. Easy to work with, fun to refinish and will look great! I just Cetoled my 5 boards with 3 coats of base and 3 of gloss. Set for another 4 years. Also, I use a very large LL Bean bag to hold them in place in the port lazerette. I am having one lexan board made to let in some light.
Good luck. Bill
Good luck. Bill
Lexan boards
While Lexan is more resistant to breakage, its also more susceptible to UV degregation. Lexan will craze and yellow faster than Acrylic. If you want them to last use Acrylic boards. Plexiglass is just a trade name for Acrylic.
After you price 1/2" or thicker Plexiglass you may find that Teak is not such a bad choice.
I suggest cutting these on a table saw with a blade made specifically for plastics. It works much better. You should also consider a nice bevel at the joints between the boards so that rain will drain out. You will want pretty thick stock so that the natural flexibility in the Acrylic will not cause them to bow outward.
I think like some other board members that teak is much more in character for CD's and I have no plans to replace my solid teak boards with plastic.
If you had a Hunter then Plex would be much more in character.
Boyd
s/v Tern
CD30 MkII
Fort Lauderdale, Fla.
After you price 1/2" or thicker Plexiglass you may find that Teak is not such a bad choice.
I suggest cutting these on a table saw with a blade made specifically for plastics. It works much better. You should also consider a nice bevel at the joints between the boards so that rain will drain out. You will want pretty thick stock so that the natural flexibility in the Acrylic will not cause them to bow outward.
I think like some other board members that teak is much more in character for CD's and I have no plans to replace my solid teak boards with plastic.
If you had a Hunter then Plex would be much more in character.
Boyd
s/v Tern
CD30 MkII
Fort Lauderdale, Fla.
-
- Posts: 625
- Joined: Feb 7th, '05, 08:47
- Location: CD 32
Re: lexan?
I tend to agree, but I can also see the benefit of clear plastic as an alternative on a rainy day spent down below working on a project or reading a good book . . .rtbates wrote:. . . a Cape Dory with lexan boards? NOT NICE! or Pretty!
-
- Posts: 630
- Joined: Feb 5th, '05, 11:38
Use MR-10 in plac of Lexan
Plain Lexan does degrade with UV exposure -- discolors and eventually cracks in a spiderweb fashion. Plain Lexan also scratches easily. MR-10, which is Lexan with a scratch and mar resistant (thus the "MR" name) coating is highly UV resisistant. It is slightly more expensive than Lexan but at the price of Lexan what's another few bucks?
A Lexan hatch board is a nice addition to any Cape Dory. It makes the cave-like interior much brighter and easier to live in. It doesn't have to be thick -- mine is 1/4" -- and it is unbelievably strong. Nice additions would be a teak frame and a slot for the locking tang with the Spartan bronze trim plates on either side. The board easily stores under a settee berth cushion. MR-10 is available in several tints. Clear works well for drop board replacement while the Light Smoke Grey seems better (to me) for replacing overhead hatch lenses.
I think McMaster-Kerr caries MR-10 but I can't put my hands on the number right now as I am in Deale, MD on a boat delivery (Herrington Harbor North, where there are several CD-s).
Check out MR-10 before deciding against this idea, IMHO it really provides a nice enhancement toward the liveability of any boat.
________
Dodge Charger Specifications
A Lexan hatch board is a nice addition to any Cape Dory. It makes the cave-like interior much brighter and easier to live in. It doesn't have to be thick -- mine is 1/4" -- and it is unbelievably strong. Nice additions would be a teak frame and a slot for the locking tang with the Spartan bronze trim plates on either side. The board easily stores under a settee berth cushion. MR-10 is available in several tints. Clear works well for drop board replacement while the Light Smoke Grey seems better (to me) for replacing overhead hatch lenses.
I think McMaster-Kerr caries MR-10 but I can't put my hands on the number right now as I am in Deale, MD on a boat delivery (Herrington Harbor North, where there are several CD-s).
Check out MR-10 before deciding against this idea, IMHO it really provides a nice enhancement toward the liveability of any boat.
________
Dodge Charger Specifications
Last edited by Andy Denmark on Feb 13th, '11, 03:18, edited 1 time in total.
- barfwinkle
- Posts: 2169
- Joined: Feb 6th, '05, 10:34
- Location: S/V Rhapsody CD25D
Lexan
Hello to All
I agree with Andy. This past winter, I cut a piece of lexan to use as an additional middle insert/drop board. I love the extra light in the cabin. I only use it while on board, otherwise I just have the original board in place. But that is some tough stuff to cut, or my saw must have been really dull.
Fair Winds from Oklahoma, where we hope to get to the boat this weekend (storms or no)!
I agree with Andy. This past winter, I cut a piece of lexan to use as an additional middle insert/drop board. I love the extra light in the cabin. I only use it while on board, otherwise I just have the original board in place. But that is some tough stuff to cut, or my saw must have been really dull.
Fair Winds from Oklahoma, where we hope to get to the boat this weekend (storms or no)!
Bill Member #250.
teak or plastic?
Being faced with the same dilema, I've decided to install a 4" bronze opening port to the center board. Keep an eye on the helmsman, let in some light, let the breeze flow, and what could be classier?!
Bill
Nor'Sea 27 "Epiphany"
formerly Cape Dory 31 "Sea Myth"
Bill
Nor'Sea 27 "Epiphany"
formerly Cape Dory 31 "Sea Myth"
-
- Posts: 24
- Joined: Apr 6th, '10, 14:34
- Location: Typhoon Weekender, Versus, #1670, Bethlehem, PA
Allen,
Just read your post about your TY #1671 and the companionway board delaminating and your thoughts about making three teak replacement boards. I own TY #1670 and have two boards vs. three vs. your one.
I believe three boards are original to the boat, but your hull number may suggest otherwise. Do you happen to know if your companionway board was original to your TY?
Just read your post about your TY #1671 and the companionway board delaminating and your thoughts about making three teak replacement boards. I own TY #1670 and have two boards vs. three vs. your one.
I believe three boards are original to the boat, but your hull number may suggest otherwise. Do you happen to know if your companionway board was original to your TY?
- Kevin Kaldenbach
- Posts: 346
- Joined: Aug 24th, '08, 16:26
- Location: Cape Dory 31 “Kerry Ann“. Currently in Corpus Christi TX and Typhoon Weekender “Wimpyâ€
reply
I had a piece of 3/4 plexiglass made to replace my lower drop board. They also made a hatch in it with a flip up lid. I had this done so that I can leave my boards in and still see and operate my GPS mounted in the companionway. Now I can pour the coals to my boat in this windy Corpus Christi bay and not worry about getting water in the cabin.
Kevin
CD 31 "Kerry Ann"
kaldenbach.us
CD 31 "Kerry Ann"
kaldenbach.us