No, not religion...
A friend at the helm, yesterday, T-boned a 35-footer. COQUINA's now wearing a pretzel on her nose instead of a bow-pulpit. Ocean Engineering's phone is disconnected -- I assume they are as well (Kathy -- make a note on the equiper's list). So who has the drawings? Does anyone know of a source -- preferably in the northeast?
WOW -- is that stem-fitting strong!
Don Sargeant
~~COQUINA~~
CD25D # 189
Unsightly in Greenwich Cove
oh-buoy@att.net
Need pulpit help
Moderator: Jim Walsh
-
Catherine Monaghan
Re: Need pulpit help
Don,
I'm going to remove Ocean Engineering from the list on the "Where to Look" page. Does anyone know of a replacement?
By the way, if you cannot find a local fabricator to make a replacement bow pulpit, Lockwood Boat Works, Inc. (the boatyard where I keep my boat) makes them. (They make the pulpits for one of the powerboat manufacturers.) It would have to be a custom order and I'm sure it would be expensive too. (You probably wouldn't get it right away either, but they do good quality work.)
Anyway, they're there if you cannot find anything closer to home or cheaper. They're located in Morgan, NJ.
They have a web site, but it's getting stepped on today by another site using the same URL as a redirect. When it's up and running again, it should be at <a href="http://www.lbwinc.com/">http://www.lbwinc.com/</a> or you can contact them at 732-721-1605.
Cathy
CD32 Realization, #3
Rahway, NJ
Raritan Bay
catherine_monaghanNOSPAM@merck.com
I'm going to remove Ocean Engineering from the list on the "Where to Look" page. Does anyone know of a replacement?
By the way, if you cannot find a local fabricator to make a replacement bow pulpit, Lockwood Boat Works, Inc. (the boatyard where I keep my boat) makes them. (They make the pulpits for one of the powerboat manufacturers.) It would have to be a custom order and I'm sure it would be expensive too. (You probably wouldn't get it right away either, but they do good quality work.)
Anyway, they're there if you cannot find anything closer to home or cheaper. They're located in Morgan, NJ.
They have a web site, but it's getting stepped on today by another site using the same URL as a redirect. When it's up and running again, it should be at <a href="http://www.lbwinc.com/">http://www.lbwinc.com/</a> or you can contact them at 732-721-1605.
Cathy
CD32 Realization, #3
Rahway, NJ
Raritan Bay
Don Sargeant wrote: No, not religion...
A friend at the helm, yesterday, T-boned a 35-footer. COQUINA's now wearing a pretzel on her nose instead of a bow-pulpit. Ocean Engineering's phone is disconnected -- I assume they are as well (Kathy -- make a note on the equiper's list). So who has the drawings? Does anyone know of a source -- preferably in the northeast?
WOW -- is that stem-fitting strong!
Don Sargeant
~~COQUINA~~
CD25D # 189
Unsightly in Greenwich Cove
catherine_monaghanNOSPAM@merck.com
-
len
Re: Need pulpit help
kathy et al
CMI in hingham, 781-740-1260, does this kind of work routinely and skillfully - they aren't cheap but i don't think you'll find quality work cheap anywhere
len
md.frel@nwh.org
CMI in hingham, 781-740-1260, does this kind of work routinely and skillfully - they aren't cheap but i don't think you'll find quality work cheap anywhere
len
md.frel@nwh.org
-
Catherine Monaghan
Here's another stainless steel fabricator...
of boat rails. They are in Michigan.
<a href="http://www.topsinquality.com/">Tops In Quality, Inc.</a>
314 E. Huron Blvd.
P.O. Box 148
Marysville, MI 48084
Tel: 810-364-7150
Fax: 810-364-7925
Email: <a href="mailto:tiq@topsinquality.com">tiq@topsinquality.com</a>
<a href="http://www.topsinquality.com/">Tops In Quality, Inc.</a>
314 E. Huron Blvd.
P.O. Box 148
Marysville, MI 48084
Tel: 810-364-7150
Fax: 810-364-7925
Email: <a href="mailto:tiq@topsinquality.com">tiq@topsinquality.com</a>
-
Gary L.
-
Don
Re: Here's another stainless steel fabricator...
Thanks Catherine,
My local rigger (Hatheway Reiser & Raymond)wants $1200. When I asked to see a sample of his work he told me his pulpits were made in Michigan. Tops-in-Q quoted $575!
My local rigger (Hatheway Reiser & Raymond)wants $1200. When I asked to see a sample of his work he told me his pulpits were made in Michigan. Tops-in-Q quoted $575!
Catherine Monaghan wrote: of boat rails. They are in Michigan.
<a href="http://www.topsinquality.com/">Tops In Quality, Inc.</a>
314 E. Huron Blvd.
P.O. Box 148
Marysville, MI 48084
Tel: 810-364-7150
Fax: 810-364-7925
Email: <a href="mailto:tiq@topsinquality.com">tiq@topsinquality.com</a>