Inline fuse

Discussions about Cape Dory, Intrepid and Robinhood sailboats and how we use them. Got questions? Have answers? Provide them here.

Moderator: Jim Walsh

Post Reply
User avatar
Ron Churgin
Posts: 184
Joined: Jul 30th, '07, 10:56
Location: "Courtship" Allied Princess Cutter,Oceanside, NY

Inline fuse

Post by Ron Churgin »

Hi,

I am not knowledgeable at all about electronics. I am finishing up an ST2000 installation and have been reading old posts in the archives.

Is there any downside to connecting the autotiller directly to the battery with an inline 5 amp fuse? This seems like the simplest, shortest wire run?

I will be disconnecting the autotiller and removing it after sailing. Am I overlooking something? Will I blow up the boat?

Any wisdom would be appreciated.
Ron Churgin
User avatar
John Vigor
Posts: 608
Joined: Aug 27th, '06, 15:58
Contact:

Seems OK

Post by John Vigor »

Ron, I don't know about wisdom, but that's exactly the way I installed my ST2000 on my CD27, with the fuse right next to the positive terminal. So far so good. No blow-up.

Cheers,

John V.
User avatar
Warren Kaplan
Posts: 1147
Joined: Feb 5th, '05, 11:44
Location: Former owner of Sine Qua Non CD27 #166 1980 Oyster Bay Harbor, NY Member # 317

Post by Warren Kaplan »

Ron,

Exactly what I did. I installed the "socket" for the tillerpilot under the coaming on the starboard side just above the lazarette. I ran the wires from the batteries, which are installed in that starboard cockpit lazarette, directly to the terminals on the tillerpilot socket. I installed an inline fuse on the positive side feed wire between the battery and the socket . I've had this setup for 4-5 years now and its worked perfectly.

The only trouble I've every had is that I made a faulty "crimp" when making one of the connections and a year later it failed. It was an easy fix though. Use good connectors. Make careful crimps if called for. Seal all crimps/splices under rubber shrink wrap. You'll have no trouble if you do it carefully!
"I desire no more delight, than to be under sail and gone tonight."
(W. Shakespeare, Merchant of Venice)
User avatar
Ron Churgin
Posts: 184
Joined: Jul 30th, '07, 10:56
Location: "Courtship" Allied Princess Cutter,Oceanside, NY

thanks for the help

Post by Ron Churgin »

Thanks guys...sounds simple...off I go crimper and wire stripper in hand to confront the dreaded Ampere Voltaic.
Ron Churgin
Neil Gordon
Posts: 4367
Joined: Feb 5th, '05, 17:25
Location: s/v LIQUIDITY, CD28. We sail from Marina Bay on Boston Harbor. Try us on channel 9.
Contact:

Post by Neil Gordon »

The only downside I see is that you can't shut down all the electical systems from the selector switch. A circuit that's connected to the batttery is always alive. (I have that for the auto bilge pump, which is my only exception.)

If you want to bypass the panel, you might wire to the selector switch instead of the battery.
Fair winds, Neil

s/v LIQUIDITY
Cape Dory 28 #167
Boston, MA

CDSOA member #698
User avatar
Steve Laume
Posts: 4127
Joined: Feb 13th, '05, 20:40
Location: Raven1984 Cape Dory 30C Hull #309Noank, CT
Contact:

Post by Steve Laume »

I wired a cigarette lighter socket for my plug in solar panel that does not turn off with the selector switch.

I came off of the feed to the selector switch to a well labeled, dedicated, breaker, separated from the main panel. This is a different situation in that I want the thing hot when everything else is turned off.

You could wire your auto pilot directly to the battery or to the out feed from the selector switch but what is the advantage? You could just as well connect it to a breaker in the normal fashion.

That would give you much more control over when the thing is off or on. If there was ever a problem you could isolate it to the auto pilot with no heroics.

I suppose there a lot more than one way to do it, Steve.
seadawg
Posts: 81
Joined: May 6th, '06, 20:05
Location: Cape Dory 22D
Corpus Christi, Tx.

(reply)

Post by seadawg »

Because of possible transient voltages generated while starting the engine it may be best to have all sensitive marine electronics off during the start. For this reason it may be best to have the auto-pilot connected to an accessary switch on the dc panel. Just a thought and what I did. Cheers, Charlie.
User avatar
Warren Kaplan
Posts: 1147
Joined: Feb 5th, '05, 11:44
Location: Former owner of Sine Qua Non CD27 #166 1980 Oyster Bay Harbor, NY Member # 317

Post by Warren Kaplan »

My tiller pilot is stored inside the cabin when not sailing. I plug it in only after the engine is started. Of course if its engaged when I'm sailing and then I want to start the engine it will be already running when I start the engine then. I'm no electrician but I don't think there is a "active" circuit if the pilot isn't plugged into the socket, even though the wires run from the battery directly to the socket.

I suppose you could not only put an inline fuse into the positive wire but also and inline "switch" to turn it on and off if you wanted.
"I desire no more delight, than to be under sail and gone tonight."
(W. Shakespeare, Merchant of Venice)
Post Reply